Application
Variants
Maintenance
Combined temperature and humidity sensor
Functional description
X-SENS-TEMP-RH-EXH sensors are control components for integration with control systems such as X-AIRCONTROL.
The sensor consists of two sensor heads for measuring temperature and relative humidity. The duct sensor variant is intended for use in circular or rectangular extract air ducts.
Measuring ranges are –40 to 120 °C and 0 to 100% relative humidity.
A Modbus RTU data interface is used to transmit measured values to the control system.
A plug-in connection cable with an RJ12 plug simplifies installation.
The zone module automatically recognises the sensor (plug and play).
Duct temperature sensor (PT1000)
Functional description
X-SENS-TEMP-PT1000 temperature sensors are control components for integration with control systems such as X-AIRCONTROL.
The temperature sensor is a PT1000 sensor. The duct sensor variant is intended for use in circular or rectangular supply air ducts, or preferably in extract air ducts, as an alternative to a room temperature sensor.
Measuring range: –40 to 85 °C.
The zone module automatically recognises the temperature sensor (plug and play).
Air quality sensor (VOC)
Functional description
X-SENS-VOC air quality sensors are control components for integration with control systems such as X-AIRCONTROL.
The air quality sensor measures the concentration of volatile organic compounds such as alcohols, aldehydes, ketones, esters, terpenes, aromatic compounds, and alkenes. The duct sensor variant is intended for use in circular or rectangular extract air ducts.
Measuring range: 450 to 2000 ppm.
A Modbus RTU data interface is used to transmit measured values to the control system.
A plug-in connection cable with an RJ12 plug simplifies installation.
The zone module automatically recognises the sensor (plug and play).
Combined CO2 and humidity sensor
Functional description
X-SENS-CO2-RH sensors are control components for integration with control systems such as X-AIRCONTROL.
The sensor consists of two sensor heads for measuring CO2 concentration and relative humidity. The room sensor variant is intended for use in a room. The precision of CO2 concentration measurements is maintained by cyclical self calibration.
Measuring ranges are 0 to 2000 ppm and 0 to 100% relative humidity.
Measured values are transmitted to the control system via 0 – 10 V DC analogue signals.
The zone module automatically recognises the sensor (plug and play).
180° motion detector
Functional description
X-SENS-PIR-SM motion detectors are control components for integration with control systems such as X-AIRCONTROL.
The motion detector includes a PIR sensor (passive infrared) for detectiong people in a room, i.e. occupancy. The flush mounted variant for mounting on a wall has an operational range of 180°.
The condition (i.e. if the room is occupied or not) is transmitted to the control system via a volt-free digital output.
360° motion detector
Functional description
X-SENS-PIR-FM motion detectors are control components for integration with control systems such as X-AIRCONTROL.
The motion detector includes a PIR sensor (passive infrared) for detectiong people in a room, i.e. occupancy. The surface mounted variant for mounting on a ceiling has an operational range of 360°.
The condition (i.e. if the room is occupied or not) is transmitted to the control system via a volt-free digital output.
Dew point monitor
Functional description
X-SENS-DEWPT dew point monitors are control components for integration with control systems such as X-AIRCONTROL.
The dew point monitor contains a humidity sensor for measuring the relative humidity near the dew point (100% rh). The goal is to ensure that the dew point is not reached, i.e. that condensation is avoided.
The condition is transmitted to the control system via a volt-free digital output.
Four-way splitter
Functional description
X-SENS-SPLITTER four-way splitters are used to connect up to three sensors and actuators to an interface, e.g. to an interface of a zone module within X-AIRCONTROL.
The four-way splitter can also serve as an adapter to connect air quality and temperature sensors to terminals in case the connection cables have bare wire ends. The actual connection to the zone modules is done with RJ12 plugs.
X-SENS-TEMP-RH-EXH
Supply voltage | 24 V DC ± 25%, from the zone module |
Power rating | 0.22 W |
Temperature measurement | |
Measuring range | –40 to 120 °C |
Measurement error | 0.25 K (15 – 40 °C) |
Humidity measurement | |
Measuring range | 0 – 100% rh |
Measurement error | <5% rh, <2% rh (10 – 90% rh) |
Long term drift | 0.5% rh per year |
Installed length | 50 – 250 mm |
Operating temperature | – 20 to 50 °C |
Max. humidity | 5 – 95% rh, no condensation |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 54 (sensor head IP 32) |
Connecting cable | 7 m, with RJ12 plug |
Installation location | Circular and rectangular ducts |
Weight | 250 g |
X-SENS-TEMP-PT1000
Sensor | PT1000 |
Resistance | 1000 Ω at 0 °C |
Measurement error | 0.5 K (–40 to 15 °C) 0.725 K (40 to 85 °C) |
Installed length | 116 mm |
Operating temperature | – 40 to 100 °C |
Max. humidity | 5 – 95% rh, no condensation |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 32 |
Connecting cable | 4 m, bare wire ends |
Installation location | Circular and rectangular ducts |
Weight | 250 g |
X-SENS-VOC
Supply voltage | 24 V DC ± 25%, from the zone module |
Power rating | 0.46 W |
Measuring range | 450 – 2000 ppm |
Measurement error | <150 ppm |
Start-up time | 15 min |
Response time | 5 min |
Installed length | 65 – 105 mm |
Operating temperature | 0 – 50 °C |
Max. humidity | 5 – 95% rh, no condensation |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 54 (sensor head IP 20) |
Connecting cable | 7 m, with RJ12 plug |
Installation location | Circular and rectangular ducts |
Weight | 175 g |
X-SENS-CO2-RH
Supply voltage | 24 V AC/DC, from the zone module |
Power rating | 1.2 W |
CO2 measurement | |
Measuring range | 0 – 2000 ppm |
Measurement error | ±30 ppm |
Start-up time | 10 min |
Humidity measurement | |
Measuring range | 0 – 100% rh |
Measurement error | 3% rh (20 – 80% rh) |
Long term drift | <10% rh per year |
Operating temperature | 0 – 50 °C |
Max. humidity | 5 – 95% rh, no condensation |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 30 |
Colour | RAL 9010, pure white |
Installation location | Wall installation |
Dimensions | 80 × 105 × 23.5 mm |
Weight | 69 g |
X-SENS-PIR-SM
Supply voltage | 24 V AC/DC ± 10%, from the zone module |
Sensor | PIR (passive infrared) |
Operational range | 180° |
Detection range | 8 m; 4 m with people sitting |
Installation, distance from floor | 1.1 to 2.2 m (4 m max.) |
Operating temperature | – 25 to 55 °C |
Max. humidity | 5 – 95% rh, no condensation |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 30 |
Connection | Screw terminals |
Colour | RAL 9010, pure white |
Installation location | Wall installation on a Ø60 mm junction box |
Dimensions | 88 × 88 × 64 mm |
Weight | 98 g |
X-SENS-PIR-FM
Supply voltage | 24 V AC/DC ± 10%, from the zone module |
Sensor | PIR (passive infrared) |
Operational range | 360° |
Detection range | 8 m; 4 m with people sitting |
Installation, distance from floor | 2.5 to 3.0 m (10 m max.) |
Operating temperature | – 25 to 55 °C |
Max. humidity | 5 – 95% rh, no condensation |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 30 |
Connection | Screw terminals |
Colour | RAL 9010, pure white |
Installation location | Wall installation |
Dimensions | 98 mm, 48 mm protruding beyond the surface |
Weight | 104 g |
X-SENS-DEWPT
Supply voltage | 24 V AC/DC ± 20%, from the zone module |
Power rating | 1.0 VA |
Switching point | 92 ±4% rh at 25 °C |
Hysteresis | 5% rh |
Response time | 3 minutes max. |
Exposure to condensation | 30 minutes max. |
Switch output | Volt-free contact, 230 V AC max., 1 A max. |
Operating temperature | 0 – 50 °C |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 30 |
Installation location | Casing suitable for installation on a wall or ceiling, sensor casing suitable for chilled surfaces |
Weight | 85 g |
X-SENS-SPLITTER
Operating temperature | 0 to 50 °C |
IEC protection class | III (protective extra-low voltage) |
Protection level | IP 20 |
Connection | 4 RJ12 sockets and 8 spring-loaded terminals, 1.5 mm² |
Installation location | Switch cabinet, wall or ceiling |
Fixing | On a mounting rail |
Dimensions | 46 × 78 × 45 |
Weight | 60 g |
Combined temperature and humidity sensor
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Combined temperature and humidity sensor for rectangular and circular extract air ducts.
Ready-to-operate sensor which consists of a casing with flange, a protective tube with two sensor heads, and a connecting cable with RJ12 plug.
Modbus RTU data interface for the transmission of measured values to the control system.
The zone module automatically recognises the sensor (plug and play).
Materials and surfaces
Technical data
Temperature measurement
Humidity measurement
Duct temperature sensor (PT1000)
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Temperature sensor for rectangular and circular extract air ducts.
Ready-to-operate sensor which consists of a protective tube with flange, a sensor head and a connecting cable.
The zone module automatically recognises the temperature sensor (plug and play).
Materials and surfaces
Technical data
Air quality sensor (VOC)
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Sensor for measuring the concentration of volatile organic compounds in rectangular and circular supply or extract air ducts.
Ready-to-operate sensor which consists of a protective tube with flange, a sensor head, and a connecting cable with RJ12 plug.
Modbus RTU data interface for the transmission of measured values to the control system.
The zone module automatically recognises the temperature sensor (plug and play).
Materials and surfaces
Technical data
Combined CO2 and humidity sensor
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Sensor for measuring the CO2 concentration and humidity in rooms.
Ready-to-operate sensor which consists of a casing with two sensor heads and connection terminals.
The zone module automatically recognises the sensor (plug and play).
Materials and surfaces
Technical data
CO2 measurement
Humidity measurement
180° motion detector
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Motion detector (occupancy).
Ready-to-operate detector which consists of a casing and a PIR sensor (passive infrared).
Switch output (volt-free contact) for the transmission of the detected condition (occupied or not occupied) to the control system.
Materials and surfaces
Technical data
360° motion detector
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Motion detector (occupancy).
Ready-to-operate detector which consists of a casing and a PIR sensor (passive infrared).
Switch output (volt-free contact) for the transmission of the detected condition (occupied or not occupied) to the control system.
Materials and surfaces
Technical data
Dew point monitor
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Sensor for monitoring the dew point on chilled surfaces.
Ready-to-operate sensor which consists of a casing and a sensor head in a separate casing.
Switch output (volt-free contact) for the transmission of the detected condition (occupied or not occupied) to the control system.
Materials and surfaces
Technical data
Four-way splitter
Components for the measurement and recording of various quantities and conditions in systems for single room control and centralised control – such as X-AIRCONTROL
Four-way splitter for the connection of four sensors or control panels (Modbus).
The four-way splitter can also serve as an adapter to connect air quality and temperature sensors to terminals in case the connection cables have bare wire ends. The actual connection to the zone modules is done with RJ12 plugs.
Materials and surfaces
Technical data
|
|
X-SENS-TEMP-RH-EXH
Application
Parts and characteristics
Materials and surfaces
X-SENS-TEMP-PT1000
Application
Parts and characteristics
Materials and surfaces
X-SENS-VOC
Application
Parts and characteristics
Materials and surfaces
X-SENS-CO2-RH
Application
Parts and characteristics
Materials and surfaces
X-SENS-PIR-SM
Application
Parts and characteristics
Materials and surfaces
X-SENS-PIR-FM
Application
Parts and characteristics
Materials and surfaces
X-SENS-DEWPT
Application
Parts and characteristics
Materials and surfaces
X-SENS-SPLITTER
Application
Materials and surfaces
Installation and commissioning
X-SENS-TEMP-RH-EXH, X-SENS-TEMP-PT1000
X-SENS-VOC
X-SENS-CO2-RH
X-SENS-PIR-SM
X-SENS-PIR-FM
X-SENS-DEWPT
X-SENS-SPLITTER
Partager la page
Recommander cette page
Recommander cette page en envoyant un lien par mail.
Partager la page
Merci pour votre recommandation !
Votre recommandation a été envoyée et devrait arriver dans les plus brefs délais.
Contact
Nous sommes à votre disposition
Veuillez préciser votre message et le type de demande
Tel.: +32 (0) 2/522 07 80
Contact
Merci pour votre message !
Votre message a été envoyé et sera traité dans les plus brefs délais.
Notre département de traitement des demandes prendra contact avec vous dès que possible.
Pour les questions d'ordre général concernant les produits ou services, vous pouvez aussi nous appeler :
Tel.: +32 (0) 2/522 07 80
Contact
Nous sommes à votre disposition
Veuillez préciser votre message et le type de demande
Tel.: +32 (0) 2/522 07 80
Contact
Merci pour votre message !
Votre message a été envoyé et sera traité dans les plus brefs délais.
Notre département de traitement des demandes prendra contact avec vous dès que possible.
Pour les questions d'ordre général concernant les produits ou services, vous pouvez aussi nous appeler :
Tel.: +32 (0) 2/522 07 80