KA2-EU

KA2-EU with spring return actuator

Thermal release unit

Conforms to VDI 6022

KA2-EU

For extract and exhaust air in commercial kitchens

Rectangular fire damper for use in extract air and exhaust air ducts of commercial kitchens. For shutting off air ducts between two fire compartments
■ National Technical Approval Z-41.3.-716
■ CE marking in accordance with EN 15650
■ Nominal sizes:

Width: 250 – 1400 mm in 25 mm increments
Height: 250 – 600 mm in 25 mm increments
Length: 580 mm up to H = 400 mm; 680 mm from H = 425 mm

■ Large free cross-section ensures maximum safety
■ Low pressure differential and sound power level
■ Easy to clean thanks to smooth surfaces and an encased linkage
■ Can be integrated into the management and control equipment (MCE) with TROXNETCOM
■ Low-maintenance spring-return actuator (1~ 230 V AC, 50 Hz, IP 54) with integrated control unit and connection casing
■ 2 thermoelectric release units with simple plug/socket mounting
■ Flow-independent design
■ No damper blade protrusion, no extension piece required
■ Short closing time of 3 s in the event of a fire
■ Approved for daily ventilation operation in accordance with DIN EN 15650 Annex C
■ EPD (Environmental Product Declaration)
■ Hygiene certificate according to VDI 6022
■ Based on fire damper FK2-EU
■ Optional dry installation with installation kit ES for a wide range of installation situations

General information

Application

TROX fire dampers with National Technical Approval and CE marking in accordance with EN 15650, for shutting off extract air and exhaust air ducts in commercial kitchens
Preventing the spread of fire and the transmission of smoke through air ducts into neighbouring fire compartments

Classification

Fire resistance classes up to: K90 (ve, ho), in accordance with abZ/aBG EI 90 (ve, ho [H], i ↔ o) S C10000, in accordance with DIN EN 13501

Variants

With installation kit ES

Nominal sizes

Width: 250 – 1400 mm in 25 mm increments
Height: 250 – 600 mm in 25 mm increments
Length: 580 mm up to H = 400 mm; 680 mm from H = 425 mm

Attachments

2 thermal release mechanisms
Z43KA Spring return actuator with integrated control unit and connection casing

Special characteristics

National Technical Approval Z-41.3.-716
CE marking in accordance with EN 15650
Tested in accordance with DIN EN 1366-2 and the additional tests required by the DIBt

Essential components KA2-EU (at least casing and shut-off damper element): non-combustible building materials, at least class A2-s1, d0 according to DIN EN 13501-1
Building materials of the other components: at least E-d2 according to DIN EN 13501-1

Large free cross-section
Low differential pressure and sound power level
Integration into the MCE with TROXNETCOM

Parts and characteristics

Installation in horizontal and vertical air ducts
Installation orientation with any airflow direction
Large free cross-section, therefore low differential pressures
Reliable closing thanks to patented high-performance spring return actuator, even with existing deposits
Release temperature 72 °C

Construction features

Dimensionally stable rectangular casing, available in 25 mm increments
Based on the FK2-EU fire damper
Rectangular or square design, dimensionally stable frame, with perforated flange on both sides
Low-maintenance spring return actuator (1~ 230 V AC, 50
Hz, IP 54) with integrated control unit and connection casing
An extremely short closing time of 3 s minimises the risk of grease fires spreading in the event of a fire
Permitted for daily ventilation operation 2 thermoelectric release units with simple plug/socket mounting
No damper blade protrusion, no extension piece required
Flow-independent design
Design in accordance with product standard DIN EN 15650 and the specifications of the DIBt
Flat, metal-coated damper blade simplifies cleaning
Manual opening by crank handle possible
Remote monitoring and integration into an MCE via TROXNETCOM systems
Optional closing by means of a push button/wall switch by interrupting the supply voltage.
Integrated limit switches for Open and Closed position
Height and width available in 25 mm increments
Connecting flanges with fixing holes on both sides, suitable for air duct connection
Locking of the actuator in the event of a fire to prevent accidental opening
Signalling of operating states via the LED on the actuator
Installation with mortar or with dry mortarless installation kit

Material and surfaces

Casing: galvanised sheet steel or optionally stainless steel 1.4301
Damper blade made of special insulating material, metalcoated, or optionally made of stainless steel 1.4301
Damper blade shaft: stainless steel 1.4301

Installation and commissioning

Install the fire damper according to the operating and installation manual.

Mortar-based installation in walls:

In solid wall
In plastered solid wall
In gypsum wallboards
In lightweight partition wall/fire wall with metal studs and cladding on both sides
In lightweight partition wall with metal stud
In lightweight partition wall with timber stud/half-timbered construction
In shaft wall with metal stud

Dry mortarless installation with KA2-EU installation kit ES in walls:

Below a flexible ceiling joint
In lightweight partition wall with metal stud
In lightweight partition wall with timber stud/half-timbered construction
In shaft wall with metal stud

Mortar-based installation into solid ceilings

Mortar-based installation into solid ceilings
Mortar-based installation into solid ceilings with concrete base

Standards, guidelines and certificates

Fire damper in accordance with EN 15650, tested in accordance with DIN EN 1366-2 and the additional tests and requirements specified by the German Institute for Building Technology (DIBt)
Proven as a multi-purpose actuator in accordance with DIN EN 15650 Annex C, approved for daily ventilation operation
National Technical Approval Z-41.3.-716
Hygiene certificate according to VDI 6022
EPD (Environmental Product Declaration) in accordance with DIN EN ISO 14025 and DIN EN 15804
Proven corrosion protection according to DIN EN 15650 in connection with DIN EN 60068-2-52
CE marking in accordance with the EC Declaration of Conformity, pursuant to the meaning of the Machinery Directive as a complete machine

Maintenance

At the instruction of the owner of the ventilation system, the function of the fire damper must be checked at least every six months in accordance with the requirements of VDI 2052, taking into account the basic maintenance measures in accordance with DIN EN 13306 in conjunction with DIN 31051. If two consecutive tests at intervals of 6 months do not reveal any functional defects, the fire damper only needs to be checked once a year.
In general, closing and reopening is sufficient, with spring return actuator also remotely operated or by means of a voltage interruption
Fire dampers must be included in the regular cleaning schedule for the ventilation and air-conditioning system. For details on maintenance and inspection, please refer to the installation and operating manual

Disclosure of Chemicals

RoHS EU Directive 2011/65/EU (RoHS)

This product or single variants comply with EU Directive 2011/65/EU (RoHS) on the restriction of the use of certain hazardous substances in electrical and electronic equipment. For more information, please refer to our Environmental Product Declarations.

REACH 1907/2006 (EC Regulation REACH)

This product or single variants comply with the provisions of EC Regulation No. 1907/2006, also known as REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals). For more information, please refer to our Environmental Product Declarations.

Information technique

1 KA2-EU
2 Spring return actuator with integrated limit switches
3 Thermal release unit
4 Connection casing
5 Crank handle
6 Position indicator

Functional description
Type KA2-EU fire dampers close off extract air and exhaust air ducts in commercial kitchens and prevent the spread of fire and smoke via air ducts into adjacent fire compartments. In standard operation, the fire damper is in the Open position. This is made possible by the electrically operated spring return actuator, which enables the motorised opening of fire damper. The spring return actuator also enables the fire damper to be activated by the management and control equipment (MCE) during maintenance work and functional checks.
In the event of a fire, one of the two thermoelectric release units is triggered. From a trigger temperature of 72 °C, the damper blade closes the fire damper within 3 seconds. In addition, an interruption in the supply voltage also causes the fire damper to close. The closing process is based on the fail-safe principle. The control system of the spring return actuator differentiates between a fire and other interruptions.
The limit switch signal can also be used to close other KA2-EU units. The signal on leaving the Open end position can be used to switch off the supply voltage to other fire dampers. Fire dampers that are further away from the fire then close within 10 seconds. TROXNETCOM offers further solutions. Limit switches can be used for position indication. When leaving the Open position, the signal from the Open limit switch must be used to switch off the fan.

Nominal sizes	250 × 250 to 1400 × 600 mm
Volume flow rate range	up to 10080 l/s or 36288 m³/h
Operating temperature	10 – 50 °C
Release temperature	72 °C
Maximum upstream velocity	≤ 12 m/s

This specification text describes the general properties of the product. Texts for variants can be generated with our Easy Product Finder design programme.

Specification text

Rectangular fire dampers in accordance with the European product standard DIN EN 15650 for supply and extract air systems in ventilation and air-conditioning installations, with additional National Technical Approval. Suitable for shutting off extract and exhaust air ducts in commercial kitchens, with a fire resistance rating of 90 minutes. Reliable closing even with existing deposits, thanks to a

maintenance-free spring-return actuator. Tested for fire protection properties in accordance with EN 1366-2. Airtight casing complying with leakage class B according to EN 1751, with thermal release at 72 °C, made of galvanised sheet steel or optionally stainless steel; airflow-independent design. Shut-off damper blade made of special insulating material, metal-clad, airtight sealing. With 2 compact thermal release devices 72 °C, 2 electrical limit switches to indicate damper position CLOSED or OPEN, fan switch-off, and integration into the MCE. Control and connection casing with plug/socket connection integrated into the spring-return actuator. Designed for 10000 cycles and a closing time of 3 s in the event of fire and 10 s in ventilation mode. Suitable for mortar-based and dry installation in solid walls or ceilings, shaft walls with metal studs, lightweight partition walls with metal or timber studs, and for connection to horizontal and vertical air ducts with a connecting flange.

Classification

Fire resistance classes up to: K90 (ve, ho), in accordance with abZ/aBG EI 90 (ve, ho [H], i ↔ o) S C10000, in accordance with DIN EN 13501

Material and surfaces

Casing: galvanised sheet steel or optionally stainless steel 1.4301
Damper blade made of special insulating material, metalcoated, or optionally made of stainless steel 1.4301
Damper blade shaft: stainless steel 1.4301

Technical data

Nominal sizes: 250 x 250 – 1400 x 600 mm
Volume flow range: max. 10080 l/s or max. 36288 m3/h
Operating temperature: 10 – 50 °C
Release temperature: 72 °C
Maximum upstream velocity: ≤ 12 m/s

Standards, guidelines and certificates

Fire damper in accordance with EN 15650, tested in accordance with DIN EN 1366-2 and the additional tests and requirements specified by the German Institute for Building Technology (DIBt)
Proven as a multi-purpose actuator in accordance with DIN EN 15650 Annex C, approved for daily ventilation operation
National Technical Approval Z-41.3.-716
Hygiene certificate according to VDI 6022
EPD (Environmental Product Declaration) in accordance with DIN EN ISO 14025 and DIN EN 15804
Proven corrosion protection according to DIN EN 15650 in connection with DIN EN 60068-2-52
CE marking in accordance with the EC Declaration of Conformity, pursuant to the meaning of the Machinery Directive as a complete machine

Nominal sizes

Width: 250 – 1400 mm in 25 mm increments
Height: 250 – 600 mm in 25 mm increments
Length: 580 mm up to H = 400 mm; 680 mm from H = 425 mm

Attachments

2 thermal release mechanisms
Z43KA Spring return actuator with integrated control unit and connection casing

Zubehör

Dry mortarless installation kit

Equivalence criteria

Free cross-section at least 70 % of the nominal size
Smooth inner surfaces without grooves to prevent deposits
Low-maintenance spring-return actuator with integrated control unit and connection casing
Independent of airflow direction – airflow in both directions without extension piece with flow guide device
10,000 cycles in accordance with DIN EN 15650, Annex C 3.2, approved for daily ventilation operation

Manufacturer

TROX SE
Type: KA2-EU

KA2-EU	–	2	/	DE	/	500 × 500 × 680	/	ES	/	Z43KA
\|		\|		\|		\|		\|		\|
1		2		3		4		5		6

1 Type
KA2-EU Fire damper for the extract air of commercial kitchens

2 Construction
No entry: standard construction
2 Stainless steel casing

3 Country of destination
Specify country code

4 Nominal size [mm]
Specify width × height × length

5 Accessories
No entry: without accessories
ES Installation kit for dry mortarless installation

6 Attachment
Z43KA Spring return actuator 230 V

Order example: KA2-EU-2/DE/500×500×680/ES/Z43KA

Type	KA2-EU – Fire damper for the extract air of commercial kitchens
Construction	Stainless steel casing
Country of destination	Germany
Nominal size [mm]	Width 500, height 500, length 680
Accessories	Installation kit for dry mortarless installation
Attachment	Spring return actuator 230 V

Téléchargements

Information produit

Product data sheet KA2-EU

KA2-EU_PD_2026_09_22_DE_en Product data sheet 390 KB pdf

Certificats

Declaration of Performance KA2-EU

KA2-EU_DoP_001_2026_05_DE_en Declaration of Performance 2,1 MB pdf
Environmental Product Declaration KA2-EU

KA2-EU_2025_03_DE_en Environmental product Declaration 1,4 MB pdf

Manuels d'utilisation

Installation and operating manual KA2-EU

KA2-EU_IOM_CD10090_V2_2026_08_GB_en Installation and operating manual 18 MB pdf

En cliquant sur ce bouton, vous nous autorisez à vous offrir une expérience de navigation et d'achat de qualité sur notre site web. Ces cookies comprennent ceux qui sont nécessaires au fonctionnement du site et au contrôle de nos services et applications, ainsi que ceux qui sont utilisés uniquement à des fins statistiques, pour des paramètres de commodité ou pour afficher un contenu personnalisé. Vous pouvez décider quelles catégories vous souhaitez autoriser et vous pouvez ajuster les paramètres d'utilisation des données en fonction de vos propres besoinsS. Veuillez noter que, selon les paramètres que vous avez sélectionnés, toutes les fonctionnalités de la page peuvent ne pas être disponibles. Vous pouvez modifier votre sélection à tout moment.

NÉCESSAIRE D’UN POINT DE VUE TECHNIQUE

Ces cookies sont nécessaires au bon fonctionnement de notre site Internet et ne peuvent pas être désactivés. En règle générale, ces cookies ne sont définis qu'en réponse aux actions que vous avez entreprises, comme la définition de vos préférences de confidentialité ou la préparation de votre panier. De plus, des fonctionnalités ou supports liés à la sécurité via un webchat dédié sont intégrés, y compris tous les cookies de session de TROX définis une fois que vous vous êtes connecté en tant que client. Vous pouvez configurer votre navigateur pour bloquer ces cookies ou vous en informer. En conséquence, cependant, certaines zones du site Web peuvent ne pas fonctionner comme prévu.

STATISTIQUES ET ANALYSE DE SITE WEB

Ces cookies permettent de collecter des données à des fins de statistiques et d'analyses afin que TROX puisse mesurer les performances des sites Web visités, identifier les problèmes techniques et trouver des points de départ pour l'optimisation. Ils peuvent être définis par nous ou par des tiers dont nous utilisons les services sur nos sites. Les utilisateurs aident également à identifier, par exemple, quelles pages sont utilisées le plus fréquemment ou rarement ou comment les gens naviguent entre les pages Web. Toutes les informations utilisées par des tiers sont agrégées et anonymisées.

KA2-EU

For extract and exhaust air in commercial kitchens

General information

Information technique

Téléchargements

Information produit

Product data sheet KA2-EU

Certificats

Declaration of Performance KA2-EU

Environmental Product Declaration KA2-EU

Manuels d'utilisation

Installation and operating manual KA2-EU

NÉCESSAIRE D’UN POINT DE VUE TECHNIQUE

STATISTIQUES ET ANALYSE DE SITE WEB

COMMODITÉ ET PERSONNALISATION

POUR LA MEILLEURE EXPÉRIENCE TROX POSSIBLE